Toyota 4Runner manuals

Toyota 4Runner: 4WD Control ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

4WD Control ECU Communication Stop Mode

Either condition is met:

  • "Four Wheel Drive Control" is not displayed on the "Bus Check" screen.
  • "4WD Control ECU Communication Stop Mode" in "DTC Combination Table" applies.
  • Power source circuit of four wheel drive control ECU
  • Four wheel drive control ECU branch line or connector
  • Four wheel drive control ECU

HINT:

For vehicles with four wheel drive only.

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE

1.

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

(a) Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).



NEXT

2.

CHECK FOR OPEN IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)

(a) Disconnect the F47 four wheel drive control ECU connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

F47-19 (CANH) - F47-20 (CANL)

Ignition switch off

54 to 69 Ω

Text in Illustration

*a

Rear view of wire harness connector

(to Four Wheel Drive Control ECU)


NG

REPAIR OR REPLACE FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)


OK

3.

CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)

(a) Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).



(b) Disconnect the F46 four wheel drive control ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F46-4 (GND) - Body ground

Always

Below 1 Ω

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

F46-3 (IG) - Body ground

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Rear view of wire harness connector

(to Four Wheel Drive Control ECU)

Result

Result

Proceed to

OK (for VF2A)

A

OK (for VF4BM)

B

OK (for VF2BM)

C

NG

D


A

REPLACE NO. 2 FOUR WHEEL DRIVE CONTROL ECU


B

REPLACE NO. 2 FOUR WHEEL DRIVE CONTROL ECU


C

REPLACE NO. 2 FOUR WHEEL DRIVE CONTROL ECU


D

REPAIR OR REPLACE HARNESS OR CONNECTOR

Center Airbag Sensor Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Center Airbag Sensor Communication Stop Mode Either condition is met: " ...

Suspension Control ECU Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Suspension Control ECU Communication Stop Mode Either condition is met: &quo ...

Other materials about Toyota 4Runner:

Terminals Of Ecu
TERMINALS OF ECU 1. RADIO AND DISPLAY RECEIVER ASSEMBLY Terminal No. (Symbols) Wiring Color Terminal Description Condition Specification G48-1 (FR+) - G48-7 (GND) P - BR ...

SFR Solenoid Circuit (C0226,C0236,C0246,C0256,C1225-C1228)
DESCRIPTION The solenoid turns on when signals are received from the skid control ECU and controls the pressure acting on the wheel cylinders, thus controlling braking force. DTC Code DTC Detection Condition Trouble Area ...

© 2016-2024 | www.to4runner.net

0.0237