Toyota 4Runner manuals

Toyota 4Runner: Air Outlet Damper Control Servo Motor Circuit (B1443/43)

DESCRIPTION

The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the No. 1 air conditioning amplifier assembly of the damper position. The No. 1 air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code

DTC Detection Condition

Trouble Area

B1443/43

The air outlet damper position does not change when the No. 1 air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo).

  • Damper servo sub-assembly (mode damper servo)
  • Air conditioning harness assembly
  • No. 1 air conditioning amplifier assembly

WIRING DIAGRAM


PROCEDURE

1.

READ VALUE USING TECHSTREAM (MODE DAMPER SERVO)

(a) Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (See page ).


Air Conditioner

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Air Outlet Servo Pulse (D)

Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255

15 (pulse): FACE 1

15 (pulse): FACE 2

41 (pulse): B/L

65 or 73 (pulse): FOOT

83 or 95 (pulse): F/D

113 (pulse): DEF

-

Air Outlet Servo Actu Pulse (D)

Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255

15 (pulse): FACE 1

15 (pulse): FACE 2

41 (pulse): B/L

65 or 73 (pulse): FOOT

83 or 95 (pulse): F/D

113 (pulse): DEF

-

OK:

The display is as specified in the normal condition column.

Result

Result

Proceed to

OK (When troubleshooting according to problem symptoms table)

A

OK (When troubleshooting according to the DTC)

B

NG

C


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


B

REPLACE NO. 1 AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.

PERFORM ACTIVE TEST USING TECHSTREAM (MODE DAMPER SERVO)

(a) Select the Active Test, use the Techstream to generate a control command, and then check that the damper servo sub-assembly (mode damper servo) operates (See page ).


Air Conditioner

Tester Display

Test Part

Control Range

Diagnostic Note

Air Outlet Servo Pulse (D)

Damper servo sub-assembly (mode damper servo) pulse

Min.: 0, Max.: 255

-

OK:

Damper servo sub-assembly (mode damper servo) operates normally.


OK

REPLACE NO. 1 AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.

REPLACE DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)

(a) Replace the damper servo sub-assembly (mode damper servo) (See page ).


HINT:

Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.

NEXT

4.

CHECK FOR DTC

(a) Clear the DTCs (See page ).


(b) Check for DTCs (See page ).


OK:

DTC B1443 is not output.


OK

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

NG

5.

REPLACE NO. 1 AIR CONDITIONING AMPLIFIER ASSEMBLY

(a) Temporarily replace the No. 1 air conditioning amplifier assembly with a new or normally functioning one (See page ).


NEXT

6.

CHECK FOR DTC

(a) Clear the DTCs (See page ).


(b) Check for DTCs (See page ).


OK:

DTC B1443 is not output.


OK

END (NO. 1 AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)


NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

Air Inlet Damper Control Servo Motor Circuit (B1442/42)
DESCRIPTION The recirculation damper servo sub-assembly sends pulse signals to inform the No. 1 air conditioning amplifier assembly of the damper position. The No. 1 air conditioning amplifier as ...

Evaporator Temperature Sensor Circuit (B1413/13)
DESCRIPTION The No. 1 cooler thermistor is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and control ...

Other materials about Toyota 4Runner:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL GENERATOR DRIVE END FRAME BEARING (a) Using SST and a press, press in a new generator drive end frame bearing. SST: 09950-60010 09951-00470 SST: 09950-70010 09951-07100 ...

© 2016-2024 | www.to4runner.net

0.007