Toyota 4Runner manuals

Toyota 4Runner: Ambient Temperature Sensor Circuit (B1412/12)

DESCRIPTION

The cooler thermistor (ambient temperature sensor) is installed in the front part of the cooler condenser assembly to detect the ambient temperature and control the air conditioning auto mode. The sensor connected to the air conditioning amplifier assembly detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the cooler thermistor (ambient temperature sensor) changes in accordance with the cooler thermistor temperature (ambient temperature). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler thermistor (ambient temperature sensor) and reads voltage changes as changes in the resistance of the cooler thermistor (ambient temperature sensor).

DTC Code

DTC Detection Condition

Trouble Area

B1412/12

An open or short in the cooler thermistor (ambient temperature sensor) circuit.

  • Cooler thermistor (ambient temperature sensor)
  • Harness or connector
  • Air conditioning amplifier assembly

WIRING DIAGRAM


PROCEDURE

1.

READ VALUE USING TECHSTREAM (AMBIENT TEMPERATURE SENSOR)

(a) Use the Data List to check if the cooler thermistor (ambient temperature sensor) is functioning properly (See page ).


Air Conditioner

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Ambient Temp Sensor

Cooler thermistor (ambient temperature sensor) /

Min: -23.3°C (-9.94°F)

Max: 65.95°C (150.71°F)

Actual ambient temperature displayed

Open in the circuit: -23.3°C (-9.94°F).

Short in the circuit: 65.95°C (150.71°F).

OK:

The display is as specified in the normal condition column.

Result

Result

Proceed to

OK (When troubleshooting according to problem symptoms table)

A

OK (When troubleshooting according to the DTC)

B

NG

C


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.

INSPECT COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)

(a) Remove the cooler thermistor (ambient temperature sensor) (See page ).




(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

10°C (50°F)

3.00 to 3.73 kΩ

15°C (59°F)

2.45 to 2.88 kΩ

20°C (68°F)

1.95 to 2.30 kΩ

25°C (77°F)

1.60 to 1.80 kΩ

30°C (86°F)

1.28 to 1.47 kΩ

35°C (95°F)

1.00 to 1.22 kΩ

40°C (104°F)

0.80 to 1.00 kΩ

45°C (113°F)

0.65 to 0.85 kΩ

50°C (122°F)

0.50 to 0.70 kΩ

55°C (131°F)

0.44 to 0.60 kΩ

60°C (140°F)

0.36 to 0.50 kΩ

Text in Illustration

*a

Sensing Portion

*b

Resistance

*c

Allowable Range

*d

Temperature

NOTICE:

  • Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
  • When measuring, the sensor temperature must be the same as the ambient temperature.

HINT:

As the temperature increases, the resistance decreases (refer to the graph).


NG

REPLACE COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)

OK

3.

CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

(a) Disconnect the A23 sensor connector.

(b) Disconnect the F42 amplifier connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A23-1 - F42-5 (TAM)

Always

Below 1 Ω

A23-2 - F42-13 (SG-2)

F42-5 (TAM) - Body ground

Always

10 kΩ or higher

F42-13 (SG-2) - Body ground


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Room Temperature Sensor Circuit (B1411/11)
DESCRIPTION The cooler thermistor (room temperature sensor) for the front seat is installed in the instrument panel to detect the room temperature and control the heater and air conditioner auto ...

Compressor Lock Sensor Circuit (B1422/22)
SYSTEM DESCRIPTION The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication. The air conditioning amplifier assembly reads the difference between comp ...

Other materials about Toyota 4Runner:

Red Indicator Remains On
DESCRIPTION This means that the DCM (Telematics Transceiver) detects a malfunction in the Safety Connect and stores a DTC. PROCEDURE 1. CHECK FOR DTC (a) Turn the ignition switch off. (b) Connect the Techstream to the DLC ...

Installation
INSTALLATION PROCEDURE 1. INSTALL REFRESHING SEAT SWITCH (a) Attach the 4 claws to install the refreshing seat switch. 2. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 3. INSTALL NO. 2 CONSOLE BOX RETAINER 4. INSTALL UPPER CONSO ...

© 2016-2024 | www.to4runner.net

0.0079