DESCRIPTION
This DTC is stored when the back door power window regulator motor is stuck.
NOTICE:
When a power window regulator is reinstalled or replaced, the power window control system must be initialized.
Back Door P/W
DTC Code |
DTC Detection Condition |
Trouble Area |
---|---|---|
B2312 |
The back door power window regulator motor is stuck. |
|
WIRING DIAGRAM
PROCEDURE
1. |
CHECK FOR DTC |
(a) Clear the DTC (See page ).
(b) Check for DTCs (See page ).
Result |
Proceed to |
---|---|
No DTCs output |
A |
DTC B2312 is output |
B |
A |
END |
|
2. |
CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Tool Setting |
Switch Condition |
Specified Condition |
---|---|---|---|
W10-14 (BUP2) - W10-1 (E4) |
2 V/DIV., 100 ms/DIV. |
Ignition switch ON, back door power window regulator switch up |
Pulse generation (See waveform 1 |
W10-13 (BDN2) - W10-1 (E4) |
2 V/DIV., 100 ms/DIV. |
Ignition switch ON, back door power window regulator switch down |
Pulse generation (See waveform 1) |
W10-12 (AUT2) - W10-1 (E4) |
2 V/DIV., 100 ms/DIV. |
Ignition switch ON, back door power window auto up or auto down function operating |
Pulse generation (See waveform 2) |
NG |
REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) |
|
3. |
CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY) |
(a) Disconnect the W9 back door power window regulator motor connector.
(b) Disconnect the W10 multiplex network door ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
W9-10 (UP) - V10-14 (BUP2) |
Always |
Below 1 Ω |
W9-7 (DOWN) - V10-13 (BDN2) |
Always |
Below 1 Ω |
W9-4 (AUTO) - V10-12 (AUT2) |
Always |
Below 1 Ω |
W9-1 (GND) - V10-1 (E4) |
Always |
Below 1 Ω |
W9-10 (UP) - Body ground |
Always |
10 kΩ or higher |
W9-7 (DOWN) - Body ground |
Always |
10 kΩ or higher |
W9-4 (AUTO) - Body ground |
Always |
10 kΩ or higher |
W9-1 (GND) - Body ground |
Always |
10 kΩ or higher |
OK |
REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
Operating Light Control Rheostat does not Change Light Brightness
DESCRIPTION
When the light control rheostat dial is turned upward, the combination meter
and vehicle interior illumination will become brighter. When the light control rheostat
dial is turned downward, the combination meter and vehicle illumination will d ...
Tire Pressure Warning Ecu
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL TIRE PRESSURE WARNING ECU
(a) Install the tire pressure warning ECU with the bolt.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(b) Connect the connector.
2. INSTA ...