Toyota 4Runner: Data List / Active Test

Toyota 4Runner Service Manual / Vehicle Exterior / Wiper / Washer / Wiper And Washer System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Data List.

(e) According to the display on the Techstream, read the Data List.

Main Body

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Rear Wiper HI SW Signal	Rear wiper HI switch / ON or OFF	ON: Rear wiper switch in HI position OFF: Rear wiper switch not in HI position	-
Rear Wiper LO SW Signal	Rear wiper LO switch / ON or OFF	ON: Rear wiper switch in LO position OFF: Rear wiper switch not in LO position	-
Rear Washer SW Signal	Rear washer switch / ON or OFF	ON: Rear washer switch on OFF: Rear washer switch off	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Rear Wiper HI SW Signal

Rear wiper HI switch / ON or OFF

ON: Rear wiper switch in HI position

OFF: Rear wiper switch not in HI position

Rear Wiper LO SW Signal

Rear wiper LO switch / ON or OFF

ON: Rear wiper switch in LO position

OFF: Rear wiper switch not in LO position

Rear Washer SW Signal

Rear washer switch / ON or OFF

ON: Rear washer switch on

OFF: Rear washer switch off

Back Door P/W

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Wiper Retracted Position	Rear wiper retracting switch signal / ON or OFF	ON: Rear wiper in retracting position OFF: Rear wiper in other position	-
Wiper Reverse Position	Rear wiper reverse position switch signal / ON or OFF	ON: Rear wiper in reverse position OFF: Rear wiper in other position	-
Back Door P/W Status	Back door power window position / Open or Close	Open: Back door window open Close: Back door window closed	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Wiper Retracted Position

Rear wiper retracting switch signal / ON or OFF

ON: Rear wiper in retracting position

OFF: Rear wiper in other position

Wiper Reverse Position

Rear wiper reverse position switch signal / ON or OFF

ON: Rear wiper in reverse position

OFF: Rear wiper in other position

Back Door P/W Status

Back door power window position / Open or Close

Open: Back door window open

Close: Back door window closed

Combination Meter

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Washer Switch	Level warning switch / ON or OFF	ON: Washer jar and tank empty OFF: Washer jar and tank full	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Washer Switch

Level warning switch / ON or OFF

ON: Washer jar and tank empty

OFF: Washer jar and tank full

2. PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Main Body

Tester Display	Test Part	Control Range	Diagnostic Note
Rear Wiper Washer Motor Relay	WASHER RR relay operation	ON/OFF	-

Back Door P/W

Tester Display	Test Part	Control Range	Diagnostic Note
Rear Wiper Active	Rear wiper motor operation	STOP/ACTIVE	-

Terminals Of Ecu

TERMINALS OF ECU 1. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (a) Remove the main body ECU (multiplex network body ECU) (See page ). (b) Measure ...

Rear Wiper does not Operate

DESCRIPTION The windshield wiper switch controls the rear wiper motor. WIRING DIAGRAM CAUTION / NOTICE / HINT HINT: Since the wiper and washer system has functions that use LIN communication, f ...

Other materials about Toyota 4Runner:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of ...

Transmitter ID not Received in Main Mode (C2126/26)
DESCRIPTION After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and the tire pressure warning light blinks for 1 minute and then comes on. When the tire pressure warning ECU successfully receives information from all the ...