Toyota 4Runner: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List.
(e) According to the display on the Techstream, read the Data List.
Driver Seat|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Reclining Rear |
Reclining switch signal (Rearward) / ON or OFF |
ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off |
- |
|
Reclining Front |
Reclining switch signal (Forward) / ON or OFF |
ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off |
- |
|
Front Vertical Down |
Front vertical switch signal (Downward) / ON or OFF |
ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off |
- |
|
Front Vertical Up |
Front vertical switch signal (Upward) / ON or OFF |
ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off |
- |
|
Lifter Switch Down |
Lifter switch signal (Downward) / ON or OFF |
ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off |
- |
|
Lifter Switch Up |
Lifter switch signal (Upward) / ON or OFF |
ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off |
- |
|
Slide Rear |
Sliding switch signal (Rearward) / ON or OFF |
ON: Sliding switch (Rearward) on OFF: Sliding switch (Rearward) off |
- |
|
Slide Front |
Sliding switch signal (Forward) / ON or OFF |
ON: Sliding switch (Forward) on OFF: Sliding switch (Forward) off |
- |
|
Seat Memory No1 |
Seat position memorized with M1 switch / Mem or Not Mem |
Mem: Memorized Not Mem: Not memorized |
- |
|
Seat Memory No2 |
Seat position memorized with M2 switch / Mem or Not Mem |
Mem: Memorized Not Mem: Not memorized |
- |
|
Seat Memory No3 |
- |
- |
This item is not supported. |
|
Ignition Switch |
Communication state of engine switch signal / ON or OFF |
ON: Engine switch on (IG) OFF: Engine switch off |
"OFF" is also displayed for this item when the engine switch is on (ACC). |
|
P Switch |
Shift lever position P signal / ON or OFF |
ON: Shift lever in P OFF: Shift lever not in P |
- |
|
Parking Brake SW |
Parking brake switch status / ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
|
Vehicle Speed |
Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual vehicle speed |
- |
|
Power Voltage |
Power supply for front power seat switch / min: 0.95 V, max: 20.84 V |
Within range of 11 to 14 V |
- |
|
Slide Position |
Seat sliding position / min: 0000, max: 65535 |
Within range of 0 to 65535 |
The displayed value decreases as the seat moves rearward. |
|
Reclining Position |
Seat reclining position / min: 0000, max: 65535 |
Within range of 0 to 65535 |
The displayed value decreases as the seat moves rearward. |
|
Front Vertical Position |
Seat front vertical position / min: 0000, max: 65535 |
Within range of 0 to 65535 |
The displayed value decreases as the seat moves downward. |
|
Lifter Position |
Seat lifter position / min: 0000, max: 65535 |
Within range of 0 to 65535 |
The displayed value decreases as the seat moves downward. |
|
Slide Pos Mem No1 |
Seat sliding position memorized with M1 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Reclining Pos Mem No1 |
Seat reclining position memorized with M1 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Frnt Vrtcl Pos Mem No1 |
Front vertical position memorized with M1 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Lifter Pos Mem No1 |
Lifter position memorized with M1 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Slide Pos Mem No2 |
Seat sliding position memorized with M2 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Reclining Pos Mem No2 |
Seat reclining position memorized with M2 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Frnt Vrtcl Pos Mem No2 |
Front vertical position memorized with M2 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Lifter Pos Mem No2 |
Lifter position memorized with M2 switch / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Slide Pos Mem No3 |
- |
- |
This item is not supported. |
|
Reclining Pos Mem No3 |
- |
- |
This item is not supported. |
|
Frnt Vrtcl Pos Mem No3 |
- |
- |
This item is not supported. |
|
Lifter Pos Mem No3 |
- |
- |
This item is not supported. |
|
Motor Status |
State of motor control/STANDBY, MOVING or LOCK |
STANDBY: Slide, reclining, front vertical and lifter motor are idle. MOVING: Slide, reclining, front vertical or lifter motor is moving. LOCK: Slide, reclining, front vertical or lifter motor is locked. |
- |
|
Slide Position Init Flag |
Seat sliding limit position memory / ON or OFF |
ON: Memorized OFF: Not memorized |
- |
|
Slide Position Rear Limit |
Seat sliding position / min: 0000, max: 65535 |
Within range of 0 to 65535 |
- |
|
Shift P sw (PMN) |
Shift lever position P signal / ON or OFF |
ON: Shift lever in P OFF: Shift lever not in P |
- |
|
Memory Button Buzzer Request |
Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG or REG WAIT |
OFF: Buzzer does not sound. MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan. |
- |
|
Driver Seat Request Command |
Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET |
OFF: No instruction MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to recall through memory call function RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seat MEM RET: Request to restore seat to memorized position |
- |
|
Driver Seat POS REQ |
Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3 |
OFF: No operation MEM1: M1 switch operation status MEM2: M2 switch operation status MEM3: Related switch does not exist. DRV1: Memory call 1 function operating DRV2: Memory call 2 function operating DRV3: Related function does not exist. |
- |
|
Away Move Range Scale |
Driver seat slide away distance / NONE, SMALL, STANDARD or LONG |
NONE: No movement SMALL: Moves short distance. STANDARD: Moves standard distance. LONG: Moves long distance. |
- |
|
Return Move |
Return destination / AVAIL or NOT AVL |
AVAIL: Return destination set NOT AVL: Return destination not set |
- |
|
Return & Away Function |
Power easy access system status / AVAIL or NOT AVL |
AVAIL: Power easy access system functioning NOT AVL: Power easy access system not functioning |
- |
|
Driver Seat Buckle SW |
Status of driver seat belt / ON or OFF |
ON: Tongue plate engaged OFF: Tongue plate not engaged |
- |
|
Return Position |
Slide return position / min.: 0000, max.: 65535 |
Within range of 0 to 65535 |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Driver Seat|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Seat Reclining |
Seat reclining operation |
Front / OFF / Rear |
- |
|
Front Vertical Operation |
Seat front vertical operation |
Up / OFF / Down |
- |
|
Lifter Operation |
Seat lifter operation |
Up / OFF / Down |
- |
|
Seat Slide Operation |
Seat sliding operation |
Front / OFF / Rear |
- |
|
Buzzer |
Buzzer operation |
ON / OFF |
- |
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK FRONT POWER SEAT SWITCH LH
(a) Disconnect the b18 and b19 connectors from the front power seat switch LH.
(b) Measure the voltage and resistance according to the value(s ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired sy ...
Other materials about Toyota 4Runner:
Operating a Bluetooth® enabled portable player
Selecting an album
Press “∨” or “∧” on .
Selecting tracks
Press “∧” or “∨” on .
Playing and pausing tracks
Press .
Fast-forwarding and reversing tracks
Press and hold “∧” or “∨” on .
Switching the display
Press .
...
Cleaning and protecting the vehicle exterior
Perform the following to protect the vehicle and maintain it in prime
condition:
• Working from top to bottom, liberally apply water to the vehicle body,
wheel wells and underside of the vehicle to remove any dirt and dust.
• Wash the vehicle body u ...
0.0268