Toyota 4Runner: Inspection

Toyota 4Runner Service Manual / Drivetrain / A750e Automatic Transmission / Transaxle / Oil Pump / Inspection

INSPECTION

PROCEDURE

1. INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

(a) Using a dial indicator, measure the inside diameter of the oil pump body bush.

Maximum inside diameter:

38.188 mm (1.50 in.)

If the inside diameter is more than the maximum, replace the oil pump body sub-assembly.

2. INSPECT STATOR SHAFT ASSEMBLY

(a) Using a dial indicator, measure the inside diameter of the stator shaft bush.

Maximum inside diameter:

Front side

21.577 mm (0.849 in.)

Rear side

32.08 mm (1.26 in.)

If the inside diameter is more than the maximum, replace the stator shaft assembly.

3. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY

(a) Push the driven gear to one side of the body.

(b) Using a feeler gauge, measure the body clearance.

Standard body clearance:

0.10 to 0.17 mm (0.00394 to 0.00669 in.)

Maximum body clearance:

0.17 mm (0.00669 in.)

If the body clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

Standard tip clearance:

0.070 to 0.150 mm (0.00276 to 0.00591 in.)

Maximum tip clearance:

0.150 mm (0.00591 in.)

If the tip clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

(d) Using a steel straightedge and feeler gauge, measure the side clearance of both gears.

Standard side clearance:

0.02 to 0.05 mm (0.000787 to 0.00197 in.)

Maximum side clearance:

0.05 mm (0.00197 in.)

If the side clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

HINT:

There are 5 different drive and driven gear thicknesses.

Drive and Driven Gear Thickness:

Mark	Thickness
0	10.74 to 10.749 mm (0.42283 to 0.42319 in.)
1	10.75 to 10.759 mm (0.42323 to 0.42358 in.)
2	10.76 to 10.77 mm (0.42362 to 0.42401 in.)
3	10.771 to 10.78 mm (0.42405 to 0.42441 in.)
4	10.781 to 10.79 mm (0.42445 to 0.42480 in.)

4. INSPECT FRONT OIL PUMP DRIVE GEAR ROTATION

(a) Place the oil pump body on the torque converter clutch.

(b) Check that the drive gear rotates smoothly.

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE AUTOMATIC TRANSMISSION CASE O-RING (a) Remove the O-ring from the oil pump assembly. 2. FIX OIL PUMP ASSEMBLY ...

Reassembly

REASSEMBLY PROCEDURE 1. INSTALL FRONT OIL PUMP OIL SEAL (a) Using SST and a hammer, tap in a new oil seal. SST: 09350-30020 09351-32140 HINT: Make sure the oil seal end is fl ...

Other materials about Toyota 4Runner:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. When installing the window frame moulding, heat the vehicle body and window frame moulding using a ...

Portable Player cannot be Registered
CAUTION / NOTICE / HINT HINT: Some versions of "Bluetooth" compatible audio players may not function, or the function may be limited using the navigation receiver assembly, even if the portable audio player itself can play files (See page ). ...