Toyota 4Runner: Inspection

Toyota 4Runner Service Manual / Drivetrain / A750e Automatic Transmission / Transaxle / Valve Body Assembly / Inspection

INSPECTION

PROCEDURE

1. INSPECT SHIFT SOLENOID VALVE SR

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body	20°C (68°F)	11 to 15 Ω

Text in Illustration

*a	Component without harness connected (Shift Solenoid Valve SR)

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Shift solenoid valve SR connector Battery negative (-) → Shift solenoid valve SR body	Valve moves and makes an operating noise

If the result is not as specified, replace the solenoid valve.

2. INSPECT SHIFT SOLENOID VALVE SL1 AND SL2

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 - 2	20°C (68°F)	5.0 to 5.6 Ω

Text in Illustration

*a	Component without harness connected (Shift Solenoid Valve)

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) with a 21 W bulb → Terminal 1 Battery negative (-) → Terminal 2	Valve moves and makes an operating noise

If the result is not as specified, replace the solenoid valve.

3. INSPECT SHIFT SOLENOID VALVE SLT AND SLU

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 -2	20°C (68°F)	5.0 to 5.6 Ω

Text in Illustration

*a	Component without harness connected (Shift Solenoid Valve)

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) with a 21 W bulb → Terminal 2 Battery negative (-) → Terminal 1	Valve moves and makes an operating noise

If the result is not as specified, replace the solenoid valve.

4. INSPECT SHIFT SOLENOID VALVE S1

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body	20°C (68°F)	11 to 15 Ω

Text in Illustration

*a	Component without harness connected (Shift Solenoid Valve S1)

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Shift solenoid valve S1 connector Battery negative (-) → Shift solenoid valve S1 body	Valve moves and makes an operating noise

If the result is not as specified, replace the solenoid valve.

5. INSPECT SHIFT SOLENOID VALVE S2

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body	20°C (68°F)	11 to 15 Ω

Text in Illustration

*a	Component without harness connected (Shift Solenoid Valve S2)

(b) Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Shift solenoid valve S2 connector Battery negative (-) → Shift solenoid valve S2 body	Valve moves and makes an operating noise

If the result is not as specified, replace the solenoid valve.

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE SHIFT SOLENOID VALVE SR (a) Remove the 2 bolts and solenoid valve. 2. REMOVE SHIFT SOLENOID VALVE SLU ...

Installation

INSTALLATION PROCEDURE 1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY (a) Install the spring and check ball body. (b) Insert the pin of the manual valve into the hole of the manual valve ...

Other materials about Toyota 4Runner:

Theft Deterrent System Presence Detection (B279C)
DESCRIPTION If an ECM that is incompatible with the engine immobiliser system is installed, the ECM stores this DTC. DTC Code DTC Detection Condition Trouble Area B279C An ECM for vehicles withou ...

Removal
REMOVAL PROCEDURE 1. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY 2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY 3. REMOVE FRONT FENDER APRON SEAL RH 4. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH 5. REMOVE NO. 1 OIL COOLER INLET HOSE AND NO ...