Toyota 4Runner manuals

Toyota 4Runner: Installation

INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page ).


PROCEDURE

1. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH


NOTICE:

When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

(a) Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the nut and bolt as shown in the illustration.

HINT:

First install the bolt, and then install the nut.

Torque:

for bolt :

7.5 N·m {76 kgf·cm, 66 in·lbf}

for nut :

42 N·m {428 kgf·cm, 31 ft·lbf}

Text in Illustration

*1

Bolt

*2

Nut

2. INSTALL REAR SEAT SHOULDER BELT GUIDE


3. INSTALL REAR SEATBACK EDGE PROTECTOR


4. INSTALL SEATBACK COVER WITH PAD


5. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


6. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH


7. INSTALL REAR SEATBACK COVER


8. INSTALL REAR SEAT SHOULDER BELT COVER


9. INSTALL SEAT BELT ANCHOR COVER CAP


10. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


11. INSTALL RECLINING ADJUSTER KNOB CAP LH


12. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


(a) Install the inner belt and connect the 3 point type belt anchor with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

NOTICE:

Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the seatback frame.

Text in Illustration

*1

Protruding Part

13. INSTALL CENTER SEATBACK ASSEMBLY


14. INSTALL SEAT CUSHION COVER WITH PAD


15. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


16. INSTALL REAR SEAT CUSHION MOULDING LH


17. INSTALL CENTER SEAT HINGE COVER RH


18. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


19. INSTALL REAR SEAT UPPER RECLINING COVER LH


20. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

(a) Install the rear No. 1 seat assembly LH (See page ).


Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. PROCEDURE 1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (a) Remove the rear No. 1 seat as ...

Rear No. 1 Seat Inner Belt Assembly(for 60/40 Split Double-folding Seat Type Lh Side)
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH (a) Install the inner belt with the bolt. Torque: 42 N·m {428 ...

Other materials about Toyota 4Runner:

Outside rear view mirrors
Mirror angle can be adjusted using the switch. To select a mirror to adjust, press the switch. 1. Left 2. Right To adjust the mirror, press the switch. 1. Up 2. Right 3. Down 4. Left Folding the mirrors Push the mirror back in the direction ...

Radio Antenna Cord
Components COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION Removal REMOVAL PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery termin ...

© 2016-2024 | www.to4runner.net

0.0068