INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT:
PROCEDURE
1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
CAUTION:
(a) Using an E10 "TORX" socket wrench, install the front seat side airbag assembly with 2 new nuts.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(b) Attach the 2 clamps to connect the front seat side airbag wire harness.
2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)
(a) Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
(b) Attach the 4 claws to install the 2 front seat headrest supports.
(c) Attach the 2 hooks to connect the separate type front seatback cover bracket to the separate type front seatback spring assembly with the nut.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
NOTICE:
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
(d) Close the 2 fasteners and separate type front seatback cover. |
|
(e) Using hog ring pliers, install 3 new hog rings. Text in Illustration
NOTICE:
|
|
(f) Attach the fastening tape to connect the airbag wire harness.
(g) Attach the 3 airbag wire harness clamps.
(h) Attach the claw to connect the airbag connector.
(i) Install the rubber band to the separate type front seat cushion spring assembly.
3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)
(a) w/ Climate Control Seat System:
(1) Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
(2) Attach the 4 claws to install the 2 front seat headrest supports.
(3) Attach the 2 hooks to connect the seatback cover bracket to the separate type front seatback spring assembly and install the nut.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
NOTICE:
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
(4) Using hog ring pliers, install 5 new hog rings. Text in Illustration
NOTICE:
|
|
(5) Attach the 7 hooks.
(6) Attach the fastening tape to connect the airbag wire harness.
(7) Attach the 3 airbag wire harness clamps.
(8) Attach the claw to connect the airbag connector.
(b) w/o Climate Control Seat System:
(1) Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
(2) Attach the 4 claws to install the 2 front seat headrest supports.
(3) Attach the 2 hooks to connect the separate type front seatback cover bracket to the separate type front seatback spring assembly and install the nut.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
NOTICE:
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
(4) Close the 2 fasteners and separate type front seatback cover.
*A |
for Cloth Seat |
*B |
for Synthetic Leather Seat |
(5) Using hog ring pliers, install 3 new hog rings. Text in Illustration
NOTICE:
|
|
(6) Attach the fastening tape to connect the airbag wire harness.
(7) Attach the 3 airbag wire harness clamps.
(8) Attach the claw to connect the airbag connector.
(9) Install the rubber band to the separate type front seat cushion spring assembly.
4. INSTALL FRONT SEATBACK BOARD CLIP (w/ Climate Control Seat System)
5. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System)
6. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat Type RH Side)
(See page )
7. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
(See page )
Acceleration Sensor Internal Circuit (C1419,C1435)
DESCRIPTION
The skid control ECU receives signals from the yaw rate and acceleration sensor
via the CAN communication system.
The yaw rate and acceleration sensor has a built-in acceleration sensor and detects
the vehicle condition using 2 circuits (GL1, ...
Switching the display
Items displayed can be switched by pressing the display change button.
Odometer
Displays the total distance the vehicle has been driven.
Trip meter
Displays the distance the vehicle has been driven since the meter was last
reset. Trip meters “A” ...