Toyota 4Runner manuals

Toyota 4Runner: Key-off Operation Function Operates even if Operating Conditions are not Satisfied

Toyota 4Runner Service Manual / Vehicle Exterior / Window / Glass / Power Window Control System / Key-off Operation Function Operates even if Operating Conditions are not Satisfied

DESCRIPTION

  • When the front doors are closed, each power window regulator motor can control its power window operation for approximately 43 seconds after the ignition switch is turned from ON to off by receiving operation permission signals from the main body ECU (instrument panel junction block). However, when approximately 43 seconds have elapsed, or a front side door is opened within approximately 43 seconds of the ignition switch being turned off, all the power window regulator motors disable manual operation.
  • During the auto function operation, when 43 seconds have elapsed and key-off operation is prohibited, the window operation stops immediately.

PROCEDURE

1.

CHECK LIN COMMUNICATION SYSTEM

(a) Check for LIN communication system DTCs related to the power window control system (See page ).


OK:

LIN communication system DTCs are not output.


NG

GO TO LIN COMMUNICATION SYSTEM

OK

2.

CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH OFF

(a) Check the power window operation function after the ignition switch is turned off (See page ).


Result

Result

Proceed to

Front side door is opened within 43 sec. but power windows can still operate

A

43 sec. pass and power windows can still operate

B


B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

A

3.

READ VALUE USING TECHSTREAM (FRONT DOOR COURTESY LIGHT SWITCH)

(a) Use the Data List to check if the main body ECU (multiplex network body ECU) is functioning properly (See page ).


Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

FL Door Courtesy SW

Front door courtesy light switch LH signal / ON or OFF

ON: Front door LH closed

OFF: Front door LH open

-

FR Door Courtesy SW

Front door courtesy light switch RH signal / ON or OFF

ON: Front door RH closed

OFF: Front door RH open

-

OK:

On tester screen, each item changes between ON and OFF according to above chart.


OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.

CHECK FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

(a) Open a front door and check that the map light illuminates (See page ).


OK:

Map light illuminates.


NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

OK

5.

CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

(a) Temporarily replace the driver side junction block with a new or normally functioning one.

(b) Check that the key-off operation function operates normally.


OK

END (DRIVER SIDE JUNCTION BLOCK ASSEMBLY IS DEFECTIVE)


NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter
DESCRIPTION When a key switch is pushed: 1) the door control receiver receives the key signal; 2) the door control receiver sends a signal to the certification ECU; 3) the main body EC ...

Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)
DESCRIPTION If any door glass or a power window regulator motor does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up function being unab ...

Other materials about Toyota 4Runner:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. When installing the window frame moulding, black out tape and outside stripe, heat the vehicle body ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE STEERING LOCK ACTUATOR ASSEMBLY (a) Using a center punch, mark the center of the tapered-head bolt. (b) Using a 3 to 4 mm (0.118 to 0.157 in.) drill, drill a hole in the 2 bolts. (c) Using a screw extractor, remo ...

© 2016-2024 | www.to4runner.net

0.0135