Toyota 4Runner: Meter Illumination does not Dim at Night

Toyota 4Runner Service Manual / Vehicle Interior / Meter / Gauge / Display / Meter / Gauge System / Meter Illumination does not Dim at Night

DESCRIPTION

If the dimmer switch is turned to TAIL, HEAD or AUTO, the main body ECU sends a TAIL relay signal, panel light illumination signal, panel relay signal and TAIL cancel OFF signal to the combination meter. Then the meter and accessory meter become dim.

HINT:

w/ TAIL Cancel Switch:

When the headlights are illuminated and the TAIL cancel switch is turned on, the meter does not dim.

WIRING DIAGRAM

PROCEDURE

1.	CHECK CAN COMMUNICATION SYSTEM

(a) Check for DTCs (See page ).

Result

Result	Proceed to
CAN communication system DTC is not output	A
CAN communication system DTC is output	B

Go to CAN COMMUNICATION SYSTEM

2.	READ VALUE USING TECHSTREAM (LIGHT CONTROL RHEOSTAT)

(a) Operate the Techstream according to the display and select the Data List (See page ).

Combination Meter

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Tail Cancel SW*	TAIL cancel switch condition/ON or OFF	on: TAIL cancel switch on off: TAIL cancel switch off	-
Rheostat value	Light control rheostat switch input/Min.: 0, Max.: 100	Light control rheostat switch is fully turned downward (0) → fully turned upward (100)	Unit: %

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Tail Cancel SW*

TAIL cancel switch condition/ON or OFF

on: TAIL cancel switch on

off: TAIL cancel switch off

Rheostat value

Light control rheostat switch input/Min.: 0, Max.: 100

Light control rheostat switch is fully turned downward (0) → fully turned upward (100)

Unit: %

*: w/ TAIL Cancel Switch

OK:

Light brightness can be changed within specified range by manual operation.

REPLACE COMBINATION METER ASSEMBLY

3.	INSPECT LIGHT CONTROL RHEOSTAT

w/o TAIL Cancel Switch:

(a) Inspect the light control rheostat.

(1) Remove the light control rheostat (See page ).

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
7 (T) - 1 (E)	Always	8 to 12 kΩ
3 (RV) - 1 (E)	Light control rheostat fully turned upward → fully turned downward	8 to 12 kΩ → Below 50 Ω

w/ TAIL Cancel Switch:

(b) Inspect the light control rheostat.

(1) Remove the light control rheostat (See page ).

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
7 (T) - 5 (TC)	TAIL cancel switch off → on	1 MΩ or higher → Below 1 Ω
7 (T) - 1 (E)	Always	8 to 12 kΩ
3 (RV) - 1 (E)	Light control rheostat fully turned upward → fully turned downward	8 to 12 kΩ → Below 50 Ω

REPLACE LIGHT CONTROL RHEOSTAT

4.	CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT)

(a) Disconnect the F14 meter connector.

(b) Disconnect the F5 rheostat connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F14-37 (RHIG) - F5-7 (T)	Always	Below 1 Ω
F14-38 (TR) - F5-3 (RV)
F14-39 (E2) - F5-1 (E)
F14-36 (TC) - F5-5 (TC)*

*: w/ TAIL Cancel Switch

REPLACE COMBINATION METER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR

Operating Light Control Rheostat does not Change Light Brightness

DESCRIPTION When the light control rheostat dial is turned upward, the combination meter and vehicle interior illumination will become brighter. When the light control rheostat dial is turned dow ...

Meter Illumination is Always Dark

DESCRIPTION This inspection is only for vehicles with automatic light control. The meter CPU receives signals from this circuit to adjust the illumination of the meter, instrument panel and access ...

Other materials about Toyota 4Runner:

Under Hood
General Maintenance GENERAL MAINTENANCE PROCEDURE 1. GENERAL NOTES Maintenance requirements vary depending on the country. Check the maintenance schedule in the owner's manual supplement. Following the maintenance schedule is mandat ...

Installation
INSTALLATION PROCEDURE 1. INSTALL BRAKE ACTUATOR BOLT CUSHION (a) Install the 3 brake actuator bolt cushions to the brake actuator bracket. 2. INSTALL BRAKE ACTUATOR CASE COLLAR (a) Install the 3 brake actuator case collars to the brake actuator bolt cush ...