Toyota 4Runner: Occupant Classification ECU Malfunction (B1795)
DESCRIPTION
DTC B1795 is stored when a malfunction is detected in the occupant classification ECU.
Troubleshoot DTC B1771 first when both DTCs B1771 and B1795 are present.
|
DTC Code |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B1795 |
Occupant classification ECU malfunction. |
Occupant classification ECU |
HINT:
- When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1795 of the occupant classification system.
- Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
(b) Clear the DTCs stored in memory (See page .gif)
).
HINT:
- First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
- Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.
(c) Turn the ignition switch off, and wait for at least 10 seconds.
(d) Turn the ignition switch to ON, and wait for at least 60 seconds.
(e) Using the Techstream, check for DTCs of the occupant classification ECU (See
page ).
OK:
DTC B1795 is not output.
HINT:
DTCs other than DTC B1795 may be output at this time, but they are not related to this check.
| OK | .gif) |
USE SIMULATION METHOD TO CHECK |
|
.gif)
|
2. |
REPLACE OCCUPANT CLASSIFICATION ECU |
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (See page
).
HINT:
Perform the inspection using parts from a normal vehicle when possible.
|
|
3. |
PERFORM ZERO POINT CALIBRATION |
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON, and wait for at least 60 seconds.
(c) Using the Techstream, perform the zero point calibration (See page
).
OK:
"Zero Point Calibration is complete." is displayed.
|
|
4. |
PERFORM SENSITIVITY CHECK |
(a) Using the Techstream, perform the sensitivity check (See page
).
Standard range:
27 to 33 kg (59.5 to 72.8 lb)
| NEXT | |
END |
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
HINT:
When DTC B1650/32 is stored as a result of troubleshooting for the airbag system,
perform troubleshooting for the occupant classification system.
(a) Connect ...
Sleep Operation Failure of Occupant Classification ECU (B1796)
DESCRIPTION
During sleep mode, the occupant classification ECU monitors the condition of
each sensor while the ignition switch is off. In this mode, if the occupant classification
ECU detects an ...
Other materials about Toyota 4Runner:
Installation
INSTALLATION
PROCEDURE
1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Install the switch to the manual valve shaft.
(b) Temporarily install the bolt.
(c) Install a new lock washer and the nut ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
(a) Install a new gasket and the differential carrier assembly with the 10 nuts
and 10 washers.
Torque:
52 N·m {530 kgf·cm, 38 ft·lbf}
2. INSTALL REAR AXLE SHAFT LH
(a) Install t ...
0.0242