Toyota 4Runner manuals

Toyota 4Runner: Park / Neutral Position Switch Circuit

DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

(a) Disconnect the B42 park/neutral position switch assembly connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (RL) - 2 (RB)

Shift lever in R

Below 1 Ω

Shift lever not in R

10 kΩ or higher

2 (RB) - 6 (PL)

Shift lever in P

Below 1 Ω

Shift lever not in P

10 kΩ or higher

Text in Illustration

*a

Component without harness connected

(Park/Neutral Position Switch Assembly)

Result

Result

Proceed to

OK

A

NG (for A750F)

B

NG (for A750E)

C


B

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

A

2.

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

(a) Disconnect the B42 park/neutral position switch assembly connector.


(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

B42-2 (RB) - Body ground

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Park/Neutral Position Switch Assembly)


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

(a) Disconnect the F95 clearance warning ECU assembly connector.

(b) Disconnect the B42 park/neutral position switch assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F95-7 (PL) - B42-6 (PL)

Always

Below 1 Ω

F95-23 (RL) - B42-1 (RL)

Always

Below 1 Ω

F95-7 (PL) - Body ground

Always

10 kΩ or higher

F95-23 (RL) - Body ground

Always

10 kΩ or higher


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK CLEARANCE WARNING ECU (a) Disconnect the F95 clearance warning ECU assembly connector. (b) Measure the voltage and resistance according to the value(s) in the table be ...

Taillight Relay Circuit
DESCRIPTION This is the power source circuit of the clearance warning ECU assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before p ...

Other materials about Toyota 4Runner:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. When installing the clip, heat the vehicle body and clip using a heat light. Standard: ...

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system. *: Use the Techstream. PRO ...

© 2016-2024 | www.to4runner.net

0.0092