Toyota 4Runner manuals

Toyota 4Runner: Precaution

PRECAUTION

1. IGNITION SWITCH EXPRESSION

HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression

Ignition Switch (position)

Engine Switch (condition)

Ignition Switch off

LOCK

Off (Lock)

Ignition Switch ACC

ACC

On (ACC)

Ignition Switch ON

ON

On (IG)

Engine Start

START

On (Start)

2. PRECAUTION

NOTICE:

  • When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected (See page ).

  • Perform the Reset Memory procedures (A/T initialization) after replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves (See page ).

    HINT:

    Reset Memory cannot be completed by only reconnecting the cable to the negative (-) battery terminal.

  • If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset (See page ).
    • The ATF has been replaced.

      HINT:

      If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.

    • Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.

CAUTION:

When using compressed air, always aim away from yourself to prevent Automatic Transmission Fluid (ATF) or kerosene from spraying on your face.

NOTICE:

  • The automatic transmission is composed of precision-made parts, necessitating careful inspection before reassembly because even a small nick could cause fluid leakage or affect performance.
  • The procedures are organized so that you work on only one component group at a time. This will help avoid confusion with similar-looking parts of different sub-assemblies being on your workbench at the same time.
  • The component groups are inspected and repaired from the converter housing side.
  • Whenever possible, complete the inspection, repair and reassembly before proceeding to the next component group. If a defect is found in a certain component group during reassembly, inspect and repair this group immediately. If a component group cannot be assembled because parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups.
  • Use of Toyota Genuine ATF WS is recommended.
  • All disassembled parts should be washed clean, and compressed air should be blown through any fluid passages and holes.
  • Dry all parts with compressed air. Never use a cloth.
  • The recommended ATF or kerosene should be used for cleaning.
  • After cleaning, the parts should be arranged in the order they were removed for efficient inspection, repairs and reassembly.
  • New discs for the brakes and clutches that will be used for replacement must be soaked in ATF for at least 15 minutes before reassembly.
  • All oil seal rings, clutch discs, clutch plates, rotating parts and sliding surfaces should be coated with ATF prior to reassembly.
  • All old gaskets and rubber O-rings must be replaced.
  • Do not apply adhesive cement to gaskets and similar parts.
  • Make sure that the ends of the snap rings are not aligned with any cutouts. Also make sure that snap rings are correctly installed to the grooves.
  • If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be replaced.
  • Check the thrust bearings and races for wear or damage. Replace them if necessary.
  • Use petroleum jelly to keep parts in place.
  • When working with FIPG material, perform the following:

    Using a razor blade and gasket scraper, remove all old FIPG material from the gasket surface.

    Clean all components thoroughly to remove all foreign matter.

    Clean both sealing surfaces with a non-residue solvent.

    Apply FIPG material in a continuous line on the sealing surface.

    Reassemble parts within 10 minutes of applying FIPG material. Failing to do so will require the FIPG material to be removed and reapplied.

Automatic Transmission System
...

Definition Of Terms
DEFINITION OF TERMS Term Definition Monitor description Description of what the ECM monitors and how it detects malfunctions (monitoring purpose ...

Other materials about Toyota 4Runner:

Luggage compartment features
Cargo hooks Vehicles with third seats Fold down the third seats. Raise the hook to use. The cargo hooks are provided for securing loose items. Vehicles without third seats Raise the hook to use. The cargo hooks are provided for securing loose items ...

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART HINT: If a trouble code is output during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "See page" below. Certification ECU DTC Code Detec ...

© 2016-2024 | www.to4runner.net

0.0267