DESCRIPTION
This DTC is stored when LIN communication between the rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
DTC Code |
DTC Detection Condition |
Trouble Area |
---|---|---|
B2324 |
No communication between the rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
HINT:
When communication between the rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
PROCEDURE
1. |
CLEAR DTC |
(a) Clear the DTCs (See page ).
|
2. |
CHECK FOR DTC |
(a) Check for DTCs (See page ).
OK:
DTC B2324 is not output.
OK |
USE SIMULATION METHOD TO CHECK |
|
3. |
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR LH) |
(a) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page ).
(b) Disconnect the K2 rear power window regulator motor assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
A-16 (LIN2) - K2-9 (LIN) |
Always |
Below 1 Ω |
A-16 (LIN2) or K2-9 (LIN) - Body ground |
Always |
10 kΩ or higher |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. |
CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND) |
(a) Disconnect the K2 rear power window regulator motor assembly LH connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
K2-1 (GND) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
K2-2 (B) - Body ground |
Always |
11 to 14 V |
*a |
Front view of wire harness connector (to Rear Power Window Regulator Motor Assembly LH) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
5. |
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
(a) Temporarily replace the rear power window regulator motor assembly LH with a new or normally functioning one (See page ).
|
6. |
CLEAR DTC |
(a) Clear the DTCs (See page ).
|
7. |
CHECK FOR DTC |
(a) Check for DTCs (See page ).
OK:
DTC B2324 is not output.
OK |
END (REAR POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE) |
NG |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Illumination for Panel Switch does not Come on with Tail Switch ON
CAUTION / NOTICE / HINT
NOTICE:
After replacing the navigation receiver assembly of vehicles subscribed to pay-type
satellite radio broadcasts, registration of the XM radio ID is necessary.
PROCEDURE
1.
CHECK VEHICLE SIGNAL (OPERAT ...
ABS Control System Malfunction (43)
DESCRIPTION
This DTC is output when the VSC system detects a malfunction in the ABS.
DTC Code
DTC Detection Condition
Trouble Area
43
A malfunction in the anti-lock brake system.
Anti-lo ...