DESCRIPTION
When the back door power window is fully closed and the rear window defogger switch is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE
1. |
PERFORM ACTIVE TEST USING TECHSTREAM (DEFOGGER RELAY [REAR]) |
(a) Using the Techstream, perform the Active Test (See page ).
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Defogger Relay (Rear) |
DEF relay operation |
OFF/ON |
- |
OK:
The DEF relay operates normally.
NG |
GO TO STEP 3 |
|
2. |
REPLACE HEATER CONTROL ASSEMBLY |
(a) Temporarily replace the heater control with a new or normally functioning one (See page ).
(b) Check the rear defogger function.
OK:
The window defogger function operates normally.
OK |
END (HEATER CONTROL ASSEMBLY IS DEFECTIVE) |
NG |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
3. |
INSPECT DEF RELAY |
(a) Remove the DEF relay from the engine room relay block, junction block. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
3 - 5 |
Battery voltage applied between terminals 1 and 2 |
Below 1 Ω |
3 - 5 |
Battery voltage not applied between terminals 1 and 2 |
10 kΩ or higher |
NG |
REPLACE DEF RELAY |
|
4. |
CHECK HARNESS AND CONNECTOR (BATTERY - DEF RELAY) |
(a) Remove the DEF relay from the engine room relay block, junction block. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Switch Condition |
Specified Condition |
---|---|---|
DEF relay terminal 2 - Body ground |
Ignition switch off |
Below 1 V |
DEF relay terminal 2 - Body ground |
Ignition switch ON |
11 to 14 V |
DEF relay terminal 5 - Body ground |
Always |
11 to 14 V |
*a |
Front view of wire harness connector (to DEF Relay) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
5. |
CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - DEF RELAY AND BODY GROUND) |
(a) Disconnect the F42 air conditioning amplifier connector.
(b) Remove the DEF relay from the engine room relay block, junction block.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
DEF relay terminal 1 - F42-38 (RDEF) |
Always |
Below 1 Ω |
F42-14 (GND) - Body ground |
Always |
Below 1 Ω |
F42-38 (RDEF) - Body ground |
Always |
10 kΩ or higher |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
6. |
INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY |
(a) Reconnect the F42 air conditioning amplifier connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
NG |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
|
7. |
CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS - DEF RELAY AND BODY GROUND) |
(a) Disconnect the W1 and W2 back door glass (window defogger wire) connectors.
(b) Remove the DEF relay from the engine room relay block, junction block.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
DEF relay terminal 3 - W1-1 |
Always |
Below 1 Ω |
W2-1 - Body ground |
Always |
Below 1 Ω |
W1-1 - Body ground |
Always |
10 kΩ or higher |
OK |
REPLACE BACK DOOR GLASS (WINDOW DEFOGGER WIRE) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL KEY INTERLOCK SOLENOID WIRE (w/o Smart Key System)
(a) Install the key interlock solenoid wire on to the install the ignition switch.
2. INSTALL IGNITION SWITCH ASSEMBLY (w/o Smart Key System)
(a) Install the ign ...
System Description
SYSTEM DESCRIPTION
1. GENERAL
(a) To assist the driver with parking the vehicle by displaying an image of the
area behind the vehicle, this system has a rear television camera assembly mounted
on the back door. The system displays the image on the naviga ...