Toyota 4Runner manuals

Toyota 4Runner: Rear Wiper does not Operate

DESCRIPTION

The windshield wiper switch controls the rear wiper motor.

WIRING DIAGRAM


CAUTION / NOTICE / HINT

HINT:

Since the wiper and washer system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

PROCEDURE

1.

READ VALUE USING TECHSTREAM (WIPER AND BACK DOOR POWER WINDOW POSITION)

(a) Use the Data List to check if the rear wiper and back power window are functioning properly (See page ).


Back Door P/W

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Wiper Retracted Position

Rear wiper retracting switch signal / ON or OFF

ON: Rear wiper in retracting position

OFF: Rear wiper in other position

-

Wiper Reverse Position

Rear wiper reverse position switch signal / ON or OFF

ON: Rear wiper in reverse position

OFF: Rear wiper in other position

-

Back Door P/W Status

Back door power window position / Open or Close

Open: Back door window open

Close: Back door window closed

-

OK:

On the Techstream screen, each item changes between ON and OFF according to the above chart.

Result

Result

Proceed to

OK

A

NG (Rear wiper position)

B

NG (Back door power window position)

C


B

GO TO STEP 4


C

GO TO POWER WINDOW CONTROL SYSTEM


A

2.

READ VALUE USING TECHSTREAM (WINDSHIELD WIPER SWITCH)

(a) Use the Data List to check if the rear wiper is functioning properly (See page ).


Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Rear Wiper HI SW Signal

Rear wiper HI switch / ON or OFF

ON: Rear wiper switch in HI position

OFF: Rear wiper switch not in HI position

-

Rear Wiper LO SW Signal

Rear wiper LO switch / ON or OFF

ON: Rear wiper switch in LO position

OFF: Rear wiper switch not in LO position

-

OK:

On the Techstream screen, each item changes between ON and OFF according to the above chart.


NG

GO TO STEP 6


OK

3.

PERFORM ACTIVE TEST USING TECHSTREAM (REAR WIPER)

(a) Using the Techstream, perform the Active Test (See page ).


Back Door P/W

Tester Display

Test Part

Control Range

Diagnostic Note

Rear Wiper Active

Rear wiper motor operation

STOP/ACTIVE

-

OK:

The rear wiper motor operates normally.


OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


NG

GO TO STEP 8

4.

CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

(a) Measure the voltage according to the value(s) in the table below.


Standard Voltage:

Tester Connection

Tool Setting

Switch Condition

Specified Condition

V2-3 (W) - V2-12 (SGND)

5 V/DIV., 10 ms/DIV.

Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off)

Pulse generation (See waveform 1)

V2-3 (W) - V2-12 (SGND)

5 V/DIV., 10 ms/DIV.

Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on)

Pulse generation (See waveform 2)

V2-4 (P) - V2-12 (SGND)

5 V/DIV., 10 ms/DIV.

Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off)

Pulse generation (See waveform 1)

V2-4 (P) - V2-12 (SGND)

5 V/DIV., 10 ms/DIV.

Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on)

Pulse generation (See waveform 2)


NG

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


OK

5.

CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the V1 rear wiper motor connector.

(b) Disconnect the V2 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V1-3 (W) - V2-3 (W)

Always

Below 1 Ω

V1-1 (P) - V2-4 (P)

Always

Below 1 Ω

V1-2 (E) - V2-12 (SGND)

Always

Below 1 Ω

V1-3 (W) - Body ground

Always

10 kΩ or higher

V1-1 (P) - Body ground

Always

10 kΩ or higher

V1-2 (E) - Body ground

Always

10 kΩ or higher


OK

REPLACE REAR WIPER MOTOR ASSEMBLY


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.

INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

(a) Remove the windshield wiper switch (See page ).



(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

A-6 (C1R) - A-2 (EW)

Rear wiper switch LO

Below 1 Ω

A-7 (+1R) - A-2 (EW)

Rear wiper switch HI

Below 1 Ω

A-6 (C1R) - A-2 (EW)

Rear wiper switch off

10 kΩ or higher

A-7 (+1R) - A-2 (EW)

Rear wiper switch off

10 kΩ or higher

A-6 (C1R) - A-7 (+1R)

Rear wiper switch off

10 kΩ or higher


NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY


OK

7.

CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

(a) Disconnect the F20 windshield wiper switch connector.

(b) Disconnect the F9 and F10 main body ECU connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F20-7 (+1R) - F10-17 (RWLS)

Always

Below 1 Ω

F20-6 (C1R) - F9-1 (RWC1)

Always

Below 1 Ω

F20-2 (EW) - Body ground

Always

Below 1 Ω

F20-7 (+1R) - Body ground

Always

10 kΩ or higher

F20-6 (C1R) - Body ground

Always

10 kΩ or higher


OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.

INSPECT REAR WIPER MOTOR ASSEMBLY

(a) Remove the rear wiper motor (See page ).



(b) Apply battery voltage to the rear wiper motor and check the operation of the rear wiper motor.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 5 (L)

Battery negative (-) → 4 (E)

Rear wiper motor operation is normal


NG

REPLACE REAR WIPER MOTOR ASSEMBLY


OK

9.

CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

(a) Disconnect the V1 rear wiper motor connector.

(b) Disconnect the V2 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V1-5 (L) - V2-2 (WIP+)

Always

Below 1 Ω

V1-4 (E) - V2-5 (WIP-)

Always

Below 1 Ω

V1-5 (L) - Body ground

Always

10 kΩ or higher

V1-4 (E) - Body ground

Always

10 kΩ or higher


OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Data List / Active Test
DATA LIST / ACTIVE TEST 1. READ DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing ...

Rear Washer does not Operate
DESCRIPTION The windshield wiper switch controls the rear washer motor and pump. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before perf ...

Other materials about Toyota 4Runner:

Rear seats
Vehicles without third row seats Rear seat Pull up the seatback angle adjustment lever until the lock is released. Vehicles with third row seats Second row seats 1. Seat position adjustment lever 2. Seatback angle adjustment lever Third row seats ...

Installation
INSTALLATION PROCEDURE 1. ADJUST COMPRESSOR OIL (a) When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve and drain the following amount of oil from the new compressor and magnet ...

© 2016-2024 | www.to4runner.net

0.0199