Toyota 4Runner: Reassembly

Toyota 4Runner Service Manual / Vehicle Interior / Interior Panels / Trim / Roof Headlining / Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) w/o Sliding Roof:

Install the No. 2 antenna cord sub-assembly (See page ).

(b) w/ Sliding Roof:

Install the No. 2 antenna cord sub-assembly (See page ).

2. INSTALL NO. 1 ROOF WIRE

(a) Apply butyl tape to the roof headlining so that the tape is aligned with the wire harness marking as shown in the illustration.

HINT:

Use butyl tape that has a width of 10 mm (0.394 in.).

Text in Illustration

*A	w/o Sliding Roof	*B	w/ Sliding Roof
*1	Wire Harness Marking	*2	Butyl Tape

(b) Align the marking tape on the No. 1 roof wire with the roof tongue of the roof headlining as shown in the part of the illustration labeled A and attach the wire to the hook.

(c) Align the marking tape on the No. 1 roof wire with the V mark on the roof headlining as shown in the part of the illustration labeled B and attach the wire to the roof headlining to install it.

HINT:

For the area in the illustration labeled E, attach the No. 1 roof wire so that its marked surface contacts the roof headlining.
Be sure to securely attach the roof wire so that it is not twisted.

(d) Attach each clamp.

(e) Turn the visor connectors approximately 90° clockwise to install them to the roof headlining.

Text in Illustration

*A	w/o Sliding Roof	*B	w/ Sliding Roof
*C	w/ EC Mirror	-	-
*1	Visor Connector	*2	Marking Tape
*3	Hook	*4	Roof Tongue
*5	V Mark	-	-

3. INSTALL VANITY LIGHT ASSEMBLY

HINT:

Use the same procedure for the other vanity light.

(a) Attach the 3 claws to install the vanity light.

4. INSTALL NO. 4 ROOF SILENCER PAD

(a) w/o Sliding Roof:

Align the No. 4 roof silencer pad with the markings on the roof headlining and install the No. 4 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.

(b) w/ Sliding Roof:

Align the No. 4 roof silencer pad with the markings on the roof headlining and install the No. 4 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.

5. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the No. 3 roof silencer pad with the markings on the roof headlining and install the No. 3 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.

6. INSTALL NO. 2 ROOF SILENCER PAD

(a) w/o Sliding Roof:

Align the 2 No. 2 roof silencer pads with the markings on the roof headlining and install the 2 No. 2 roof silencer pads to the position shown in the illustration using hot-melt glue or double-sided tape.

(b) w/ Sliding Roof:

Align the No. 2 roof silencer pad with the markings on the roof headlining and install the No. 2 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.

7. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the No. 1 roof silencer pad with the markings on the roof headlining and install the No. 1 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof) (a) Remove the No. 1 roof silencer pad. 2. REMOVE NO. 2 ROOF SILENCER PAD (a) w/o Sliding Roof: Remove the 2 No. 2 ...

Installation

INSTALLATION CAUTION / NOTICE / HINT HINT: A bolt without a torque specification is shown in the standard bolt chart (See page ). PROCEDURE 1. INSTALL DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. ...

Other materials about Toyota 4Runner:

Adjustment
ADJUSTMENT CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT (a) Prepare the vehicle: Ma ...

No Sound can be Heard from Speakers
PROCEDURE 1. CHECK AUDIO SETTINGS (a) In sound output setting mode, set volume, fader and balance to the initial values and check that the sound is normal. OK: Audio system returns to normal. HINT: Sound quality adjustm ...