Toyota 4Runner: Removal

Toyota 4Runner Service Manual / Vehicle Interior / Seat / Front Seat Assembly(for Power Seat) / Removal

REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page ).

If the side airbag was deployed, replace the separate type front seatback assembly with the necessary parts in accordance with the extent of the collision damage.

2. REMOVE FRONT SEAT HEADREST ASSEMBLY

(a) Remove the front seat headrest assembly.

3. REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH

(a) Operate the power seat switch (slide switch) to move the front seat assembly to the rearmost position.

(b) Using a moulding remover, detach the 2 claws.

(c) Move the front seat inner track bracket cover LH in the direction of the arrow to detach the 2 guides and remove the front seat inner track bracket cover LH.

4. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH

(a) Using a moulding remover, detach the 2 claws.

(b) Move the front seat outer track bracket cover LH in the direction of the arrow to detach the 2 claws and guide, and remove the front seat outer track bracket cover LH.

5. REMOVE INNER SEAT TRACK BRACKET COVER LH

(a) Operate the power seat switch (slide switch) to move the front seat assembly to the foremost position.

(b) Using a moulding remover, detach the 2 claws.

(c) Move the inner seat track bracket cover LH in the direction of the arrow to detach the 2 guides and remove the inner seat track bracket cover LH.

6. REMOVE OUTER SEAT TRACK COVER LH

(a) Using a moulding remover, detach the 2 claws.

(b) Move the outer seat track cover LH in the direction of the arrow to detach the 4 guides and remove the outer seat track cover LH.

7. REMOVE FRONT SEAT ASSEMBLY

(a) Remove the 2 bolts.

(b) Operate the power seat switch (slide switch) to move the front seat assembly to the rearmost position.

(d) Operate the power seat switch (slide switch) to move the front seat assembly to the center position, and operate the power seat switch (reclining switch) to move the seatback to the upright position.

(e) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

(f) Disconnect the connectors under the seat.

(g) Remove the front seat assembly.

NOTICE:

Be careful not to damage the vehicle body.

Inspection

INSPECTION PROCEDURE 1. INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (a) for Driver Side: (1) Check the operation of the separate type front seat cushion spring assembly ...

Installation

INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT: Use the same procedure for the RH and LH sides. The procedu ...

Other materials about Toyota 4Runner:

Rear Coil Spring
Components COMPONENTS ILLUSTRATION Removal REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE REAR WHEEL 2. REMOVE REAR STAB ...

Radio Broadcast cannot be Received or Poor Reception
CAUTION / NOTICE / HINT NOTICE: After replacing the navigation receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary. PROCEDURE 1. CHECK NAVIGATION RECEIVER ASSEMBLY ...