Toyota 4Runner manuals

Toyota 4Runner: Terminals Of Ecu

TERMINALS OF ECU

1. TERMINALS OF ECU

Text in Illustration

*a

Component without harness connected

(Skid Control ECU)

-

-

Terminal No. (Symbol)

Terminal Description

A6-1 (GND1)

Skid control ECU ground

A6-2 (+BM1)

Power supply for motor

A6-3 (FR+)

Front speed sensor RH power supply output

A6-4 (FL-)

Front speed sensor LH input

A6-5 (RR+)

Rear speed sensor RH power supply output

A6-6 (RL-)

Rear speed sensor LH input

A6-7 (STP)

Stop light switch assembly

A6-9 (CSW)

VSC OFF switch

A6-11 (CANH)

CAN communication terminal H

A6-12 (SP1)

Speedometer signal

A6-13 (ATRC)*2

A-TRAC switch

A6-16 (STPO)

Stop light switch assembly

A6-17 (FR-)

Front speed sensor RH input

A6-18 (FL+)

Front speed sensor LH power supply output

A6-19 (RR-)

Rear speed sensor RH input

A6-20 (RL+)

Rear speed sensor LH power supply output

A6-24 (TS)

Sensor test terminal (Signal check switch)

A6-25 (CANL)

CAN communication terminal L

A6-27 (EXI)*2

for Part-time 4WD: A.D.D. detection switch

for Full-time 4WD: Center differential lock detection switch

A6-31 (+BS)

Power supply for solenoid

A6-32 (GND2)

Skid control ECU ground

A6-40 (EXI3)

w/ Rear Differential Lock: Rear differential lock detection switch

w/o Rear Differential Lock*1: IG power supply

w/o Rear Differential Lock*2: Front wheel drive ECU

A6-41 (LBL)

Brake fluid level warning switch

A6-44 (HDCS)*3

Downhill assist control switch

A6-45 (STP2)

Stop light switch assembly

A6-46 (IG1)

IG1 power supply

A7-1 (IG2)

IG2 power supply

A7-2 (+BM2)

Power supply for motor

A7-4 (GND3)

Skid control ECU ground

  • *1: for 2WD
  • *2: for 4WD
  • *3: w/ Downhill Assist Control

2. TERMINAL INSPECTION

(a) Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.

Text in Illustration

*a

Front view of wire harness connector

(to Skid Control ECU)

-

-

Terminal No. (Symbol)

Wiring Color

Terminal Description

Condition

Specified Condition

A6-1 (GND1) - Body ground

W-B

Ground

Always

Below 1 Ω

A6-2 (+BM1) - Body ground

B

Power supply for motor

(from battery)

Always

11 to 14 V

A6-7 (STP) - Body ground

L

Stop light switch assembly

Brake pedal depressed → released

8 to 14 V → Below 1.5 V

A6-9 (CSW) - Body ground

V-W

VSC OFF switch input

VSC OFF switch off → on and held

10 kΩ or higher → Below 1 Ω

A6-13 (ATRC) - Body ground*1

LG

A-TRAC switch input

A-TRAC switch off → on and held

10 kΩ or higher → Below 1 Ω

A6-16 (STPO) - Body ground

LG-B

Stop light switch assembly

Always

11 to 14 V

A6-31 (+BS) - Body ground

L-R

Power supply for solenoid

(from battery)

Always

11 to 14 V

A6-32 (GND2) - Body ground

W-B

Ground

Always

Below 1 Ω

A6-41 (LBL) - Body ground

V-G

Brake fluid level warning switch

Brake fluid level +/-5 mm (+/-0.197 in.) from minimum level → maximum level

Below 1 Ω → 1.9 to 2.1 kΩ

A6-44 (HDCS) - Body ground*2

P

Downhill assist control switch input

Downhill assist control switch off → on

10 kΩ or higher → Below 1 Ω

A6-45 (STP2) - Body ground

V-G

Stop light switch assembly

Brake pedal depressed → released

8 to 14 V → Below 1.5 V

A6-46 (IG1) - Body ground

G

IG1 power supply

Ignition switch off → ON

Below 1 V → 11 to 14 V

A7-1 (IG2) - Body ground

W

IG2 power supply

Ignition switch off → ON

Below 1 V → 11 to 14 V

A7-2 (+BM2) - Body ground

B

Power supply for motor

(from battery)

Always

11 to 14 V

A7-4 (GND3) - Body ground

W-B

Ground

Always

Below 1 Ω

  • *1: for 4WD
  • *2: w/ Downhill Assist Control
Diagnosis System
DIAGNOSIS SYSTEM 1. DIAGNOSIS (a) If the skid control ECU detects a malfunction, the ABS and/or BRAKE warning lights and the slip indicator lights come on in accordance with the trouble area to ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. DTC CHECK / CLEAR (when Using Techstream) (a) Check for DTCs. (1) Connect the Techstream to the DLC3. (2) Turn the ignition switch to ON. (3) Turn the Techstream on. (4) Ent ...

Other materials about Toyota 4Runner:

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART DTC Code Detection Item See page 11 Short in Motor LH 12 Short in Motor RH 21 Short to ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE AUTOMATIC TRANSMISSION CASE O-RING (a) Remove the O-ring from the oil pump assembly. 2. FIX OIL PUMP ASSEMBLY (a) Place the oil pump body on the torque convert ...

© 2016-2024 | www.to4runner.net

0.0266