Toyota 4Runner: Transfer Indicator Switch

Toyota 4Runner Service Manual / Drivetrain / Vf2a Transfer / 4wd / Awd / Transfer Indicator Switch

Components

COMPONENTS

ILLUSTRATION

Inspection

INSPECTION

PROCEDURE

1. INSPECT TRANSFER INDICATOR SWITCH (4WD POSITION)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
1 - 2	Pushed	Below 1 Ω
1 - 2	Not pushed	100 kΩ or higher

If the resistance is not as specified, replace the switch.

2. INSPECT TRANSFER INDICATOR SWITCH (L4 POSITION)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
1 - 2	Pushed	Below 1 Ω
1 - 2	Not pushed	100 kΩ or higher

If the resistance is not as specified, replace the switch.

3. INSPECT TRANSFER INDICATOR SWITCH (NEUTRAL POSITION)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
1 - 2	Pushed	Below 1 Ω
1 - 2	Not pushed	100 kΩ or higher

If the resistance is not as specified, replace the switch.

Removal

REMOVAL

PROCEDURE

1. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER

(a) Remove the automatic transmission (See page ).

2. REMOVE TRANSFER INDICATOR SWITCH (4WD POSITION)

(a) Using SST, remove the indicator switch and gasket.

SST: 09817-16011

3. REMOVE TRANSFER INDICATOR SWITCH (L4 POSITION)

(a) Using SST, remove the indicator switch and gasket.

SST: 09817-16011

4. REMOVE TRANSFER INDICATOR SWITCH (NEUTRAL POSITION)

(a) Using SST, remove the indicator switch and gasket.

SST: 09817-16011

Installation

INSTALLATION

PROCEDURE

1. INSTALL TRANSFER INDICATOR SWITCH (4WD POSITION)

(a) Using SST, install a new gasket and the indicator switch.

SST: 09817-16011

Torque:

37 N·m {377 kgf·cm, 27 ft·lbf}

2. INSTALL TRANSFER INDICATOR SWITCH (L4 POSITION)

(a) Using SST, install a new gasket and the indicator switch.

SST: 09817-16011

Torque:

37 N·m {377 kgf·cm, 27 ft·lbf}

3. INSTALL TRANSFER INDICATOR SWITCH (NEUTRAL POSITION)

(a) Using SST, install a new gasket and the indicator switch.

SST: 09817-16011

Torque:

37 N·m {377 kgf·cm, 27 ft·lbf}

4. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER

(a) Install the automatic transmission (See page ).

Transfer Case Rear Oil Seal

Components COMPONENTS ILLUSTRATION Replacement REPLACEMENT PROCEDURE 1. DRAIN TRANSFER OIL 2. REMOVE REAR PROPELLER SHAFT ASSEMBLY (a) Remove the rear propeller shaft (See page ). ...

Transfer Oil

On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. CHECK TRANSFER OIL (a) Remove the filler plug and gasket. (b) Check that ...

Other materials about Toyota 4Runner:

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Rear View Monitor System DTC No. Detection Item Link C1622 Back Camera Disconnected ...

Removal
REMOVAL PROCEDURE 1. REMOVE JACK BOX HOLE COVER 2. REMOVE REAR QUARTER PANEL MUDGUARD LH 3. REMOVE REAR QUARTER PANEL MUDGUARD RH HINT: Use the same procedure as for the LH side. 4. REMOVE REAR BUMPER COVER 5. REMOVE NO. 3 FLOOR WIRE 6. RE ...