Toyota 4Runner manuals

Toyota 4Runner: Zero Point Calibration of Yaw Rate Sensor Undone (C1210,C1336)

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

The DTCs are also stored when the calibration has not been completed.

DTC Code

DTC Detection Condition

Trouble Area

C1210

Zero point calibration of the yaw rate sensor is incomplete.

  • Zero point calibration incomplete
  • Sensor installation
  • Yaw rate and acceleration sensor
  • Master cylinder solenoid (Skid control ECU)

C1336

Zero point calibration of the acceleration sensor is incomplete.

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (See page ).


CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page ).


PROCEDURE

1.

CHECK DTC (CAN COMMUNICATION SYSTEM)

(a) Check for DTCs (See page ).


Result

Result

Proceed to

CAN DTC is not output

A

CAN DTC is output

B


B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

A

2.

PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR

(a) Perform zero point calibration of the yaw rate and acceleration sensor (See page ).


NEXT

3.

PERFORM TEST MODE (SIGNAL CHECK)

(a) Turn the ignition switch off.

(b) Perform the signal check in the Test Mode Procedure (See page ).


OK:

All test mode DTCs are cleared.


OK

END

NG

4.

CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

(a) Turn the ignition switch off.

(b) Check that the yaw rate and acceleration sensor has been installed properly (See page ).


OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.


NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

OK

5.

READ VALUE USING TECHSTREAM (YAW RATE AND ACCELERATION SENSOR)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Deceleration Sensor

Acceleration sensor/ Min.: -18.183 m/s2, Max.: 18.183 m/s2

-

Changes continuously during acceleration/deceleration.

Deceleration Sensor2

Acceleration sensor 2/ Min.: -18.183 m/s2, Max.: 18.183 m/s2

-

Changes continuously during acceleration/deceleration.

Yaw Rate Sensor

Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s

Vehicle stationary: 0°/s

Right turn: -128 to 0°/s

Left turn: 0 to 127°/s

-

Yaw Rate Sensor2

Yaw rate sensor 2/ Min.: -128°/s, Max.: 127°/s

Vehicle stationary: 0°/s

Right turn: -128 to 0°/s

Left turn: 0 to 127°/s

-

(f) Check that the yaw rate and acceleration sensor output value is displayed on the Techstream.

OK:

The yaw rate and acceleration sensor output value is normal.

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page ).



OK

REPLACE MASTER CYLINDER SOLENOID


NG

REPLACE YAW RATE AND ACCELERATION SENSOR

ECU Initial Setting Incomplete (C120A)
DESCRIPTION w/ Downhill Assist Control or w/ Crawl Control: When the master cylinder solenoid (skid control ECU) is replaced, the master cylinder solenoid (skid control ECU) must be informed that ...

Acceleration Sensor Stuck Malfunction (C1232,C1243,C1245,C1279)
DESCRIPTION The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system. If there is trouble in the bus lines between the yaw rate and accelera ...

Other materials about Toyota 4Runner:

Brake Actuator (Skid Control ECU) Communication Stop Mode
DESCRIPTION Detection Item Symptom Trouble Area Brake Actuator (Skid Control ECU) Communication Stop Mode Either condition is met: "Skid Control (ABS/VSC/TRAC)" is not displa ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. READ DATA LIST HINT: Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful be ...

© 2016-2024 | www.to4runner.net

0.0067