Toyota 4Runner: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List.
(e) According to the display on the Techstream, read the Data List.
Main Body|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
RR Door Courtesy SW |
Rear door courtesy light switch RH signal / ON or OFF |
ON: Rear door RH open OFF: Rear door RH closed |
- |
|
RL Door Courtesy SW |
Rear door courtesy light switch LH signal / ON or OFF |
ON: Rear door LH open OFF: Rear door LH closed |
- |
|
FR Door Courtesy SW |
Front door courtesy light switch RH signal / ON or OFF |
ON: Front door RH closed OFF: Front door RH open |
- |
|
FL Door Courtesy SW |
Front door courtesy light switch LH signal / ON or OFF |
ON: Front door LH closed OFF: Front door LH open |
- |
2. PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Main Body|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Running Board Forced Retracting |
Perform a forcedly stowing operation of the automatic running board. |
OFF / ON |
Operate with ignition switch ON and the vehicle stopped. |
HINT:
When the automatic running board is deployed, turning the Active Test "Power Running Forced Retracting" to ON will stow the automatic running board.
Diagnosis System
DIAGNOSIS SYSTEM
1. FUNCTION OF AUTOMATIC RUNNING BOARD WARNING LIGHT
(a) When a malfunction is detected in the automatic running board system, the
automatic running board warning light in the com ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Turn the side auto step switch assembly to OFF.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Ent ...
Other materials about Toyota 4Runner:
AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION
This DTC is stored when a video or audio signal is interrupted due to battery
voltage input to the radio and display receiver assembly dropping temporarily.
DTC No.
Detection Item
DTC Detection Condition
...
Speaker Output Short (B15C3)
DESCRIPTION
This DTC is stored when a malfunction occurs in the speakers.
DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
...
0.027