Toyota 4Runner: Installation

Toyota 4Runner Service Manual / Vehicle Interior / Supplemental Restraint Systems / Rear Airbag Sensor / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PROCEDURE

1. INSTALL REAR AIRBAG SENSOR LH

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

(d) Check that the rear airbag sensor is not loose.

(e) Connect the connector.

2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

3. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER

4. INSTALL FRONT DECK SIDE TRIM COVER LH

5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

6. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

7. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

8. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

9. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

10. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

11. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

12. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

13. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

14. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

15. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board)

16. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

17. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

18. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

19. INSTALL REAR DOOR SCUFF PLATE LH

20. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

21. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

22. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

(a) Install the rear No. 2 seat assembly (See page ).

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

24. CHECK SRS WARNING LIGHT

(a) Check the SRS warning light (See page ).

Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE ...

Other materials about Toyota 4Runner:

Automatic running boards
The Automatic running boards are linked to the side door operations, extending and retracting when a side door is opened and closed. When a door is opened or closed, the board on the same side extends or retracts. 1. Opening a door: The appropriate boar ...

Back Door ECU Communication Stop (B1287)
DESCRIPTION This DTC is stored when LIN communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) stops for 10 seconds or more. DTC Code DTC Detection Condition Tr ...

Toyota 4Runner: Installation

Removal

Rear Floor Airbag Sensor

Other materials about Toyota 4Runner: