Toyota 4Runner: XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the satellite radio antenna assembly which is connected to the stereo component tuner assembly.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B15FE |
The satellite radio antenna assembly is not connected. |
|
|
B15FF |
A short occurs in the satellite radio antenna assembly. |
CAUTION / NOTICE / HINT
NOTICE:
After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).
PROCEDURE
|
1. |
CHECK CONNECTION OF SATELLITE RADIO ANTENNA CABLE |
(a) Check if the satellite radio antenna cable is securely connected to the stereo component tuner assembly.
OK:
Satellite radio antenna cable is securely connected.
| NG | .gif) |
SECURELY CONNECT SATELLITE RADIOANTENNA CABLE |
|
.gif)
|
2. |
REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 3 antenna cord sub-assembly (See page
.gif)
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
3. |
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 2 antenna cord sub-assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
4. |
REPLACE SATELLITE RADIO ANTENNA ASSEMBLY |
(a) Replace the satellite radio antenna assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
5. |
REPLACE NO. 2 INSTRUMENT PANEL WIRE |
(a) Replace the No. 2 instrument panel wire (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
6. |
REPLACE STEREO COMPONENT TUNER ASSEMBLY |
(a) Replace the stereo component tuner assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
| NG | |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
Sending Malfunction (Navigation to APGS) (U0073,U0140)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the CAN communication circuit.
DTC No.
DTC Detection Condition
Trouble Area
U0073
...
Speaker Output Short (B15C3)
DESCRIPTION
This DTC is stored when a malfunction occurs in the speakers.
DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is d ...
Other materials about Toyota 4Runner:
Noise Occurs
PROCEDURE
1.
NOISE CONDITION
(a) Check from which direction the noise comes (front left or right, or rear
left or right).
OK:
The location of the noise source can be determined.
NG
GO TO STEP 3
...
Inspection
INSPECTION
PROCEDURE
1. INSPECT FRONT DRIVE SHAFT ASSEMBLY
NOTICE:
Keep the drive shaft level while handling it.
(a) Check if there is excessive play in the outboard joint.
(b) Check if the inboard joint shaft slides smoothly in the thrust direction.
...
0.0135