Toyota 4Runner: XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the satellite radio antenna assembly which is connected to the stereo component tuner assembly.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B15FE |
The satellite radio antenna assembly is not connected. |
|
|
B15FF |
A short occurs in the satellite radio antenna assembly. |
CAUTION / NOTICE / HINT
NOTICE:
After replacing the navigation receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.
PROCEDURE
|
1. |
CHECK CONNECTION OF SATELLITE RADIO ANTENNA CABLE |
(a) Check if the satellite radio antenna cable is securely connected to the stereo component tuner assembly.
OK:
Satellite radio antenna cable is securely connected.
| NG | .gif) |
SECURELY CONNECT SATELLITE RADIOANTENNA CABLE |
|
.gif)
|
2. |
REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 3 antenna cord sub-assembly (See page
.gif)
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
3. |
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 2 antenna cord sub-assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
4. |
REPLACE SATELLITE RADIO ANTENNA ASSEMBLY |
(a) Replace the satellite radio antenna assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
5. |
REPLACE NO. 2 INSTRUMENT PANEL WIRE |
(a) Replace the No. 2 instrument panel wire (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
|
|
6. |
REPLACE STEREO COMPONENT TUNER ASSEMBLY |
(a) Replace the stereo component tuner assembly (See page
).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check if the same DTC are output again.
OK:
No DTCs are output.
| OK | |
END |
| NG | |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
Stereo Component Amplifier Disconnected (B15D3)
DESCRIPTION
The navigation receiver assembly and stereo component amplifier assembly are
connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigat ...
Sending Malfunction (Navigation to APGS) (U0073,U0140)
DESCRIPTION
These DTCs are stored when a malfunction occurs in the CAN communication circuit.
DTC No.
DTC Detection Condition
Trouble Area
U0073
...
Other materials about Toyota 4Runner:
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE STEERING LOCK ACTUATOR ASSEMBLY
(a) Using a center punch, mark the center of the tapered-head bolt.
(b) Using a 3 to 4 mm (0.118 to 0.157 in.) drill, drill a hole in the 2 bolts.
(c) Using a screw extractor, remo ...
Reverse Signal Circuit
DESCRIPTION
The radio and display receiver assembly receives a reverse signal from the park/neutral
position switch assembly.
WIRING DIAGRAM
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
(a) Disconnect the G ...
0.0083