Toyota 4Runner manuals

Toyota 4Runner: Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Data List.

(e) According to the display on the Techstream, read the Data List.

Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ACC SW

Ignition switch ACC signal / ON or OFF

ON: Ignition switch ACC

OFF: Ignition switch off

-

IG SW

Ignition switch ON signal / ON or OFF

ON: Ignition switch ON

OFF: Ignition switch off

-

RR Door Courtesy SW

Rear door courtesy light switch RH signal / ON or OFF

ON: Rear door RH open

OFF: Rear door RH closed

-

RL Door Courtesy SW

Rear door courtesy light switch LH signal / ON or OFF

ON: Rear door LH open

OFF: Rear door LH closed

-

FR Door Courtesy SW

Front door courtesy light switch RH signal / ON or OFF

ON: Front door RH open

OFF: Front door RH closed

-

FL Door Courtesy SW

Front door courtesy light switch LH signal / ON or OFF

ON: Front door LH open

OFF: Front door LH closed

-

Back Door

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Back Door Courtesy Switch

Back door courtesy light switch signal / ON or OFF

ON: Back door open

OFF: Back door closed

-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Main Body

Tester Display

Test Part

Control Range

Diagnostic Note

Illuminated Entry System

Map light and No. 1 room light

ON/OFF

-

Side Mirror Foot Light

Door mirror foot light

ON/OFF

-

Fr Foot Light

Interior foot light

ON/OFF

-

Relay for Interior Light Auto Cut Function*

DOME relay

ON/OFF

-

  • *: After turning the ignition switch to ON, proceed to the preceding screen of the active test screen with the Techstream and turn the ignition switch off, and perform the active test.
Back Door

Tester Display

Test Part

Control Range

Diagnostic Note

Luggage Compartment Light

Spot light

ON/OFF

-

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (a) Remove the main body ECU (See page ). (b) Measure the voltage and resistance accor ...

ACC Signal Circuit
DESCRIPTION This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits rel ...

Other materials about Toyota 4Runner:

Black Screen
PROCEDURE 1. CHECK DISPLAY SETTING (a) Check that the display is not in screen off mode. OK: The display setting is not in screen off mode. NG CHANGE SCREEN TO SCREEN ON MODE ...

BUS IC Communication Malfunction (B1497/97)
DESCRIPTION The air conditioning harness assembly connects the No. 1 air conditioning amplifier assembly and each servo motor. The No. 1 air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the ai ...

© 2016-2024 | www.to4runner.net

0.0066