Toyota 4Runner: Data Signal Circuit between Navigation Receiver Assembly and Extension Module

Toyota 4Runner Service Manual / Audio / Visual / Telematics / Navigation / Multi Info Display / Navigation System / Data Signal Circuit between Navigation Receiver Assembly and Extension Module

DESCRIPTION

The stereo component tuner assembly sends the sound data signal or image data signal from a device to the navigation receiver assembly via this circuit.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the navigation receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT TUNER ASSEMBLY)

(a) Disconnect the s1 and t1 navigation receiver assembly connectors.

(b) Disconnect the s2 and t2 stereo component tuner assembly connectors.

Standard Resistance:

Tester Connection	Condition	Specified Condition
s1-1 (USV4) - s2-1 (USV4)	Always	Below 1 Ω
s1-2 (US4-) - s2-2 (US4-)	Always	Below 1 Ω
s1-3 (US4+) - s2-3 (US4+)	Always	Below 1 Ω
s1-4 (UGD4) - s2-4 (UGD4)	Always	Below 1 Ω
s1-5 (USG4) - s2-5 (USG4)	Always	Below 1 Ω
t1-4 (+B2) - t2-4 (+B2)	Always	Below 1 Ω
t1-3 (ACC2) - t2-3 (ACC2)	Always	Below 1 Ω
t1-8 (GND2) - t2-8 (GND2)	Always	Below 1 Ω
s1-1 (USV4) - Body ground	Always	10 kΩ or higher
s1-2 (US4-) - Body ground	Always	10 kΩ or higher
s1-3 (US4+) - Body ground	Always	10 kΩ or higher
s1-4 (UGD4) - Body ground	Always	10 kΩ or higher
s1-5 (USG4) - Body ground	Always	10 kΩ or higher
t1-4 (+B2) - Body ground	Always	10 kΩ or higher
t1-3 (ACC2) - Body ground	Always	10 kΩ or higher
t1-8 (GND2) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.	REPLACE NO. 1 NAVIGATION WIRE

(a) Replace the No. 1 navigation wire (See page ).

(b) Check that the malfunction disappears.

OK:

Malfunction disappears.

END (NO. 1 NAVIGATION WIRE IS DEFECTIVE)

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier

DESCRIPTION The navigation receiver assembly sends a sound signal to the stereo component amplifier assembly via the sound signal circuit. The sound signal that has been sent is amplified by the s ...

Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter

DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit. The sound signal that has been sent is ampli ...

Other materials about Toyota 4Runner:

Glossary Of Sae And Toyota Terms
GLOSSARY OF SAE AND TOYOTA TERMS This glossary lists all SAE-J1930 terms and abbreviations used in this manual in compliance with SAE recommendations, as well as their TOYOTA equivalents. SAE Abbreviation SAE Term TOYOTA ...

Stereo Component Amplifier Malfunction (B15A3)
DESCRIPTION This DTC is stored when a malfunction occurs in the stereo component amplifier assembly. DTC No. DTC Detection Condition Trouble Area B15A3 When one of the conditions below is met: ...