Toyota 4Runner: Operation Check

Toyota 4Runner Service Manual / Vehicle Interior / Door Lock / Wireless Door Lock Control System(w/o Smart Key System) / Operation Check

OPERATION CHECK

1. NOTICES WHEN CHECKING

(a) Wireless door lock/unlock function:

This function operates only when the vehicle is in its initial condition (the following 3 conditions are met).

No key is inserted into the ignition key cylinder.
All the doors are closed.
HINT:

The unlock function operates even when one of the doors is open.
The power door lock system is functioning normally.

(b) The operational range of the wireless transmitter differs depending on the situation.

The operating range differs depending on the user, the way the transmitter is held and the location.
In certain areas, the operating range will be reduced due to the vehicle body shape and the influence of the surrounding environment.
The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The operating range of the transmitter may be reduced or the transmitter may not function.
When the battery weakens, the operating range is reduced and the transmitter may not function.
HINT:

If the transmitter has had prolonged exposure to direct sunlight, such as being left on the instrument panel, the battery may weaken or other problems may occur.

2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

HINT:

The switches described below transmit signals and are built into the door control transmitter.
The operating range of the transmitter must be taken into account while checks are being made.

(a) Make sure the vehicle is in a condition in which the wireless control functions can be operated (see above).

(b) Check the basic functions:

Check that all the doors lock when the lock switch is pressed.
Check that all the doors unlock when the unlock switch is pressed.

When a switch is pressed, check that the corresponding operation occurs only once. When the switch is held down, check that the corresponding operation occurs only once and does not repeatedly activate. Lastly, when the switch is pressed at 1 second intervals, check that the corresponding operation activates once for each press of the switch.

(d) Check the answer-back function:

When the lock switch is pressed, check that the hazard warning lights flash once and the buzzer sounds once simultaneously with the locking operation of all the doors.
When the unlock switch is pressed once, check that the hazard warning lights flash twice and the buzzer sounds twice simultaneously with the unlocking operation of the driver side door.

(e) Check the automatic locking function:

When all the doors are unlocked with the unlock switch and none of the doors are opened or locked within 60 seconds, check that the doors are relocked automatically.

(f) Check the switch operation fail-safe function:

If the key is in the ignition key cylinder, check that the doors cannot be locked by the lock switch. However, this does not apply when the system is in recognition code registration mode.

(g) Check the illuminated entry function:

When the map light door switch is on and all the doors are locked, pressing the unlock switch causes the interior light to illuminate and all the doors to unlock simultaneously.
If the doors have not been opened, the interior light turns off in approximately 15 seconds.

(h) Check the door ajar warning function:

If a door is open or not completely closed, check that the doors cannot be locked by the lock switch and the buzzer sounds for 5 seconds.
HINT:

The buzzer stops sounding if one of the following conditions is met:
- The buzzer has sounded for 5 seconds.
- The ignition switch is turned to ACC or to ON.
- All the doors are closed.

(i) Check the panic alarm function.

Check that the horn sounds, the headlights and taillights flash and the interior lights remain on (when the light switch is turned to the door position) for 60 seconds by the theft alarm function when the panic switch is held down for 0.8 seconds or more. Also, check that the horn stops sounding and the lights stop flashing when any switch of the transmitter is pressed.

How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: The wireless door lock control system troubleshooting procedures are based on the premise that the power door lock control system is operating normally. ...

Registration

REGISTRATION PROCEDURE 1. DESCRIPTION OF CODE REGISTRATION HINT: Recognition code registration is necessary when replacing door control transmitter or door control receiver. Add mo ...

Other materials about Toyota 4Runner:

Inspection
INSPECTION PROCEDURE 1. INSPECT MAGNET CLUTCH ASSEMBLY (a) Check the magnet clutch operation. (1) Confirm that the magnet clutch hub and magnet clutch rotor lock when the positive (+) lead of the battery is connected to terminal 3 of the magnet clutch, ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" ...