OPERATION CHECK
1. INSPECT DRIVER SIDE SEAT BELT WARNING LIGHT
(a) Turn the ignition switch to ON.
(b) When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds. After 1.8 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(c) Lift up the vehicle using a swing arm type lift (See page
).
(d) Start the engine.
(e) Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
(1) Step 1:
When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.
(2) Step 2:
When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.
After 59.6 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(3) Step 3:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(4) Step 4:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(5) Step 5:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
2. INSPECT FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
(a) Place a weight of 20 kg (44.0 lb) on the front passenger seat.
NOTICE:
Place the weight on the seat cushion and allow it to come into contact with the seatback.
(b) Turn the ignition switch to ON.
(c) Fasten the driver seat belt.
(d) When the front passenger seat belt is not fastened with the front passenger seat occupied, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.
After 1.8 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(e) Lift up the vehicle using a swing arm type lift (See page
).
(f) Start the engine.
(g) Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
(1) Step 1:
When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.
(2) Step 2:
When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.
After 59.6 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(3) Step 3:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(4) Step 4:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
(5) Step 5:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.
(6) Step 6:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
3. INSPECT SEAT BELT WARNING BUZZER
HINT:
The seat belt warning buzzer can be customized. Make sure that this function
is ON (See page ).
(a) Place a weight of 20 kg (44.0 lb) on the front passenger seat.
NOTICE:
Place the weight on the seat cushion and allow it to come into contact with the seatback.
(b) After turning the ignition switch to ON, if the driver seat belt is not fastened within 1.8 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at 1.2 second intervals for 6 seconds.
(c) Lift up the vehicle using a swing arm type lift (See page
).
(d) Start the engine.
(e) When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds once.
(f) When 30 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 9.6 seconds.
(g) After the seat belt warning buzzer has been sounding for 9.6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 20 seconds.
(h) Check that the seat belt warning buzzer in the combination meter assembly stops 29.6 seconds after it started sounding at an interval of 1.2 seconds.
(i) After the seat belt warning buzzer in the combination meter assembly stops, the ignition switch is turned off and the engine is restarted, check that the buzzer sounds once again and then sounds according to the appropriate pattern when the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened.
(j) After the seat belt warning buzzer in the combination meter assembly stops and the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt fastened, when the driver or front passenger seat belt is unfastened, check that the buzzer sounds once again and then sounds according to the appropriate pattern.
(k) After the seat belt warning buzzer in the combination meter assembly stops sounding and the shift lever is moved to R and then back to D, when the vehicle is driven at 20 km/h (12 mph) or more with the driver or front passenger seat belt not fastened, check that the buzzer sounds once again and then sounds according to the appropriate pattern.
Steering Angle Sensor Internal Circuit (C1433)
DESCRIPTION
Steering angle sensor signals are sent to the skid control ECU via the CAN communication
system. When there is a malfunction in the CAN communication system, it is detected
by the steering angle sensor zero point malfunction diagnostic functio ...
Short in Front Passenger Side Squib Circuit (B1805/52-B1808/52)
DESCRIPTION
The front passenger side squib circuit consists of the center airbag sensor and
instrument panel passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected ...