Toyota 4Runner: Reassembly

Toyota 4Runner Service Manual / Vehicle Exterior / Exterior Panels / Trim / Front Bumper(w/ Intuitive Parking Assist System) / Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL FOG LIGHT ASSEMBLY LH

2. INSTALL FOG LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

3. INSTALL FRONT BUMPER MOULDING SUB-ASSEMBLY

(a) Attach the 4 claws and 12 guides to install the front bumper moulding sub-assembly.

(b) Install the 15 outside moulding retainers and 4 screws.

4. INSTALL FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY LH

(a) Attach the 2 claws and guide to install the front bumper side moulding sub-assembly LH.

(b) Install the 2 screws and 3 outside moulding retainers.

5. INSTALL FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

6. INSTALL NO. 2 RADIATOR GRILLE MOULDING

(a) Attach the 4 claws to install the No. 2 radiator grille moulding.

(b) Install the 2 outside moulding retainers and 4 screws.

7. INSTALL FRONT BUMPER LOWER SIDE SUPPORT LH

(a) Attach the 5 claws.

(b) Install the front bumper lower side support LH with the 2 clips.

8. INSTALL FRONT BUMPER LOWER SIDE SUPPORT RH

HINT:

Use the same procedure as for the LH side.

9. INSTALL FRONT BUMPER SIDE MOULDING LH

(a) Attach the claw to install the front bumper side moulding LH.

(b) Install the 2 outside moulding retainers.

10. INSTALL FRONT BUMPER SIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.

11. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ License Plate Bracket)

(a) Install the front bumper extension mounting bracket with the 2 screws.

12. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

13. INSTALL ULTRASONIC SENSOR CLIP

14. INSTALL NO. 1 ULTRASONIC SENSOR

15. INSTALL NO. 2 ENGINE ROOM WIRE

(a) Attach the 9 clamps.

(b) Connect each connector and install the No. 2 engine room wire.

16. INSTALL RADIATOR GRILLE

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE RADIATOR GRILLE 2. REMOVE NO. 2 ENGINE ROOM WIRE (a) Disconnect each connector. (b) Detach the 9 clamps to remove the No. 2 engine room wire. 3. REMOVE NO. 1 ...

Installation

INSTALLATION CAUTION / NOTICE / HINT HINT: A bolt without a torque specification is shown in the standard bolt chart (See page ). PROCEDURE 1. INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY LH ...

Other materials about Toyota 4Runner:

4wd Control Ecu
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH 2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH 3. REMOVE COWL SIDE TRIM BOARD RH 4. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER S ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for both the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL FRONT BUMPER BAR REINFORCEMENT LH (w/o Intuitive Parking Assist System) ...