Child restraint systems are classified into the following 3 types according to the age and size of the child:
Rear facing — Infant seat/convertible seat
Forward facing — Convertible seat
Booster seat
Selecting an appropriate child restraint system
• Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt.
• If the child is too large for a child restraint system, sit the child on a rear seat and use the vehicle’s seat belt.
CAUTION
Child restraint precautions
• For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior.
• Toyota strongly urges the use of a proper child restraint system that conforms to the size of the child, installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.
• Never install a rear-facing child restraint system on the front passenger seat
even if the “AIR BAG OFF” indicator light is illuminated. In the event of an
accident, the force of the rapid inflation of the front passenger airbag can
cause death or serious injury to the child if the rear-facing child restraint
system is installed on the front passenger seat.
• A forward-facing child restraint system may be installed on the front passenger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat.
Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light illuminated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.
CAUTION
Child restraint precautions
• Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of a sudden stop, sudden swerve or an accident.
• Do not allow the child to lean his/her head or any part of his/her body
against the door or the area of the seat, front and rear pillars or roof side
rail from which the SRS side airbags or SRS curtain shield airbags deploy even
if the child is seated in the child restraint system. It is dangerous if the SRS
side airbags and SRS curtain shield airbags inflate, and the impact could cause
death or serious injury to the child.
• Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or an accident.
When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death.
If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
When the child restraint system is not in use
• Keep the child restraint system properly secured on the seat even if it is not in use. Do not store the child restraint system unsecured in the passenger compartment.
• If it is necessary to detach the child restraint system, remove it from the
vehicle or store it securely in the luggage compartment. This will prevent it
from injuring passengers in the event of a sudden stop, sudden swerve or
accident.
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL SHIFT LOCK CONTROL ECU SUB-ASSEMBLY
(a) Attach the 3 claws to install the shift lock control ECU to the transmission
floor shift.
(b) Connect the shift lock solenoid connector to the shift lock control ECU.
2. INSTALL IND ...
Removal
REMOVAL
PROCEDURE
1. TABLE OF BOLT, SCREW AND NUT
HINT:
All bolts, screws and nuts relevant to installing and removing the instrument
panel are shown along with their alphabet code in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL ...